02GN084 is a chemically cured, chrome-free, two-component epoxy polyamide primer.
- Corrosion inhibiting
- Chemical and solvent resistant
- Resistant to hydraulic fluids, lubricating oils, phosphate ester based hydraulic fluids, Skydrol® hydraulic fluid and distilled water
Unit of Measure
Components
|
Specifications
|
Instructions for Use
|
Application Guidelines
|
Equipment
|
Physical Properties
|
Storage Recommendations
|
Health Precautions
|
Note
Components
Components |
N/A
Mix Ratio (by Volume)
|
Note for Components |
N/A
If additional thinning is required use MIL-T-81772 Type II approved thinner where VOC regulations permit. See Instructions for Use section for more details. Available in touch up kits. For more details see Instructions For Use Section. |
Specifications
Specifications |
N/A
02GN084 primer is qualified to:
Product Compatibility: 02GN084 primer is compatible with the following topcoat specifications:
|
Surface Preparation and Pretreatments |
N/A 02GN084 can be applied over clean, dry, intact aluminum and composite surfaces. Aluminum surfaces shall be treated with materials conforming to MIL-DTL-5541 or equivalent. |
Induction Time |
N/A Not Required |
Color |
N/A Light Aqua Green |
Instructions for Use
Mixing Instructions |
N/A
Stir or shake the base component to ensure any pigment, which may have settled on the bottom of the can, has been fully incorporated into the base. Do not stir or shake the base component longer than 5 minutes. Slowly add one part by volume of catalyst to one part by volume base component. Mix by hand stirring, paint shaker or mechanical mixing to ensure the base/catalyst mixture is homogeneous. Do not shake or mechanically mix material for longer than 10 minutes. Constant agitation of the material during spray application is recommended. If additional thinning is required, use IS-237 or other MIL-T-81172 Type II approved thinner. Note that addition of MIL-T-81172 will increase the mixed VOC, therefore consult regional VOC regulations and restrictions. 02GN084 is available in 2-ounce and 4-ounce touch up kits: All touch-up kit configurations consist of an inner cup, which contains the 02GN084CAT catalyst located inside an outer cup (bottle) that contains the 02GN084 base component. To mix, remove lid, pour contents of inner cup (catalyst) into outer cup (base). Replace lid and shake well by hand, approximately 2 minutes. Material is now ready to apply. Note: It is important to condition the paint for 24 hours prior to mixing by placing all materials in the shop or hangar, with ambient temperatures between 13 ºC and 35 ºC (55 ºF to 95 ºF). The minimum temperature of the paint components should be 13 ºC (55 ºF) prior to mixing. |
Kit Size GK (02GN084 Base) |
N/A 96 oz2.84 L |
Kit Size GK (02GN084CAT) |
N/A 32 oz946 mL |
Kit Size GK (Yield) |
N/A 1 gal3.8 L |
Kit Size QK (02GN084 Base) |
N/A 24 oz710 mL |
Kit Size QK (02GN084CAT) |
N/A 8 oz234 mL |
Kit Size QK (Yield) |
N/A 1 dry qt946 mL |
Viscosity (Can Kits) at 23 Degree Celsius (ºC) (73 Degree Fahrenheit (ºF)) Temperature (#2 EZ Zahn Cup) |
N/A 20 ± 2 seconds |
Maximum Viscosity (Can Kits) at 23 Degree Celsius (ºC) (73 Degree Fahrenheit (ºF)) Temperature (#4 Ford Cup) |
N/A 40 seconds |
Note for Viscosity |
N/A Viscosities quoted are typical values obtained when using specified mix ratio. |
Pot Life at 21 to 25 Degree Celsius (ºC) (70 to 77 Degree Fahrenheit (ºF)) Temperature |
N/A 4 hour |
Application Guidelines
Recommended Application Conditions - Temperature |
N/A 15 to 30 ºC59 to 86 ºF |
Recommended Application Conditions - Relative Humidity (RH) |
N/A 20 to 90 % |
Spray Application |
N/A Ground the aircraft and the application equipment before priming. Stir the primer slowly during the application. The suggested film thickness is 15 to 22.5 microns (0.6 to 0.9 mils). This can be accomplished by one medium coat with 50% overlap. |
Touch-Up-Kit Application |
N/A
After mixing the touch up kit, use brush or roller to apply. These application guidelines represent PPG's best advice in standard conditions. Some parameters will be influenced by environmental conditions, equipment settings, and other variables. |
Theoretical Coverage at 25 Microns (µm) Dry Film Thickness |
N/A 19 m²/L |
Theoretical Coverage at 1 Mil Dry Film Thickness |
N/A 778 ft²/gal |
Recommended Dry Film Thickness |
N/A 0.6 to 0.9 mil15 to 22.5 c |
2 Ounce (oz) Touch Up Kit Theoretical Coverage at 25 Microns (µm) (1 Mil) Dry Film Thickness |
N/A 12.15 ft² |
4 Ounce (oz) Touch Up Kit Theoretical Coverage at 25 Microns (µm) (1 Mil) Dry Film Thickness |
N/A 24.3 ft² |
Dry Film Density |
N/A 1.57 g/cm³13.10 lb/gal |
Dry Film Weight at 25 Microns (µm) Dry Film Thickness |
N/A 3.70 g/m² |
Dry Film Weight at 1 Mil Dry Film Thickness |
N/A 0.00815 lb/ft² |
Equipment
| Equipment Type1 | N/A Conventional Air Spray Gun Electrostatic Air Assisted Airless Spray Gun Electrostatic Air Spray Gun High Volume Low Pressure Spray Gun (HVLP) |
Tip Size for Electrostatic Air Spray Gun |
N/A 1.2 mm1.5 mm |
Tip Size for Electrostatic Air Assisted Airless Spray Gun |
N/A #611 #613 (Graco Nomenclature) |
Tip Size for High Volume Low Pressure Spray Gun (HVLP) |
N/A 1.0 to 1.4 mm |
Tip Size for Conventional Air Spray Gun |
N/A 1.2 to 1.8 mm |
Pot Pressure for Electrostatic Air Spray Gun |
N/A 10 to 20 psi0.69 to 1.4 bar |
Pot Pressure for Electrostatic Air Assisted Airless Spray Gun |
N/A 700 to 1200 psi48 to 82 bar |
Pot Pressure for High Volume Low Pressure Spray Gun (HVLP) |
N/A 10 to 20 psi0.69 to 1.4 bar |
Pot Pressure for Conventional Air Spray Gun |
N/A 10 to 20 psi0.69 to 1.4 bar |
Atomization Pressure at the Cap for Electrostatic Air Spray Gun |
N/A 45 to 60 psi3.1 to 4.1 bar |
Atomization Pressure at the Cap for Electrostatic Air Assisted Airless Spray Gun |
N/A 40 to 60 psi2.8 to 4.1 bar |
Maximum Atomization Pressure at the Cap for High Volume Low Pressure Spray Gun (HVLP) |
N/A 10 psi0.69 bar |
Maximum Atomization Pressure at the Cap for Conventional Air Spray Gun |
N/A 45 to 60 psi3.1 to 4.1 bar |
Equipment Cleaning |
N/A Use IS-237 Epoxy Reducer (MIL-T-81772B Type II) to remove any liquid or residual primer from equipment. Once material has cured, use an approved chemical paint removal system to strip primer from parts and equipment |
Physical Properties
Gloss |
N/A Not Applicable |
Maximum Tack Free Dry Time at 22 to 28 Degree Celsius (ºC) (71 to 84 Degree Fahrenheit (ºF)) Temperature |
N/A 5 hour |
Topcoat Window Dry Time at 22 to 28 Degree Celsius (ºC) (71 to 84 Degree Fahrenheit (ºF)) Temperature |
N/A 5 to 24 hour |
Maximum Dry Hard Time at 22 to 28 Degree Celsius (ºC) (71 to 84 Degree Fahrenheit (ºF)) Temperature |
N/A 8 hour |
Maximum Full Cure Dry Time at 22 to 28 Degree Celsius (ºC) (71 to 84 Degree Fahrenheit (ºF)) Temperature |
N/A 14 days |
Note for Dry Times |
N/A Dry times above were established at room (ambient) temperatures, 75° ± 5°F and 50% ± 10% relative humidity at approximately 0.6-1.0 mils of dry film build. After 8 hours cure, solvent wipe the entire primed surface. After 24 hours of cure, scuff sand the entire primed surface followed by solvent wiping prior to top coating. [Ref: T.O. 1-1- 8 Section 6.12.2.5, JAN 12, 2010]. Note: Higher temperatures will reduce the recoat time while lower temperatures will increase the recoat times. |
Forced Dry Schedule |
N/A For dry to stack conditions only. Allow a minimum of 15 minutes flash off time at ambient temperatures prior to exposing painted parts to high temperatures. Complete testing should be done prior to use. Below are suggested starting points. Other variables may affect these cure schedules. |
Flash Off Time at 120 Degree Fahrenheit (ºF) Temperature |
N/A 45 minutes |
Flash Off Time at 140 Degree Fahrenheit (ºF) Temperature |
N/A 30 minutes |
Flash Off Time at 160 Degree Fahrenheit (ºF) Temperature |
N/A 20 minutes |
Flash Off Time at 180 Degree Fahrenheit (ºF) Temperature |
N/A 15 minutes |
Note for Flash Off Time |
N/A Ambient temperatures are defined as 70 ºC ± 10 ºF and 50% ± 10% relative humidity. |
| Volatile Organic Compounds (VOC) Volume2 | N/A 338 g/L |
Test Method for Volatile Organic Compounds (VOC) |
N/A Environmental Protection Agency (EPA) Method 24 |
Base Component Volume |
N/A 405 g/L |
Catalyst Component Volume |
N/A 190 g/L |
Flash Point Closed Cup Base Component Temperature |
N/A 8 ºC46 ºF |
Flash Point Closed Cup Catalyst Component Temperature |
N/A 8 ºC46 ºF |
Shelf Life |
N/A
Can kits: 12 months from date of manufacture Touch up kits: 4 months from date of packaging Note: Shelf life is provided for original, unopened containers |
Storage Recommendations
Storage Recommendations |
N/A
Inspect the condition of the container to ensure compliance. The material should be stored at temperatures between 21 ºC to 32 ºC (70 ºF to 90 ºF to ensure shelf life. Note: When procuring to a qualified material specification, follow those storage instructions. |
Health Precautions
Health Precautions |
N/A This product is safe to use and apply when recommended precautions are followed. Before using this product, read and understand the Safety Data Sheet (SDS), which provides information on health, physical and environmental hazards, handling precautions and first aid recommendations. An SDS is available on request. Avoid overexposure. Obtain medical care in case of extreme overexposure. |
Note
Note |
N/A
The application and performance property values above are typical for the material, but not intended for use in specifications or for acceptance inspection criteria because of variations in testing methods, conditions and configurations. For industrial use only. Keep away from children. All recommendations, statements, and technical data contained herein are based on tests we believe to be reliable and correct, but accuracy and completeness of said tests are not guaranteed and are not to be construed as a warranty, either expressed or implied. User shall rely on his own information and tests to determine suitability of the product for the intended use and assumes all risks and liability resulting from his use of the product. Seller's and manufacturer's sole responsibility shall be to replace that portion of the product of this manufacturer which proves to be defective. Neither seller nor manufacturer shall be liable to the buyer or any third person for any injury, loss, or damage directly or indirectly resulting from use of, or inability to use, the product. Recommendations or statements other than those contained in a written agreement signed by an officer of the manufacturer shall not be binding upon the manufacturer or seller. |
- 1 02GN084 primer is compatible with all current forms spray equipment.
- 2 Mixed, ready to use VOC
